-
Similar Topics
-
By starwoodtech
I have a 65 Inch LG OLED evo AI C4 4K Smart TV 2024 - Model OLED65C4PUA.ACC. here have been a many weird things happening. This is one of them:
I have 2 HDMI 2.1 cables attached to a Rogers Internet TV unit (HDMI 4) and the other 2.1 cable plugged into an XBOX Series X (HDMI 3). If the TV is on an HDMI 4 is active, and I turn on the XBOX (HDMI 3), the TV begins to swtich back and forth constantly and never ends until I turn off the TV. It will automatically switch itself from HDMI 4 to 3, then 3 to 4, then back to 3 again non-stop.
If I power off the XBOX, this behaivor stops.
Would anyone know why this does that? Is this a software or hardware problem? I tried to describe this to LG Support but they had no answers.
-
By pivotCE
Well, it’s 2024 and technology continues to advance. The TouchPad isn’t new by any means, but that doesn’t mean it can’t be slightly modernized to be more convenient today. Specifically, it is entirely possible to convert the TouchPad’s Micro USB port to USB C for charging and USB storage access. I’ll show you how.
This is a tough mod which requires micro-soldering and modifying a PCB which you will have a hard time sourcing a replacement for without buying another TouchPad. Proceed at your own peril.
Tools for the Job
To do this mod you’ll need a few things for tools and parts. Here’s a list of what I used:
– Needle nose pliers/tweezers
– USB C boards with 5.1k resistors
link hidden, please login to view
– Soldering iron, solder, flux and a hot air station
– Flush cuts
– Dremel with cutting or sanding wheel
– 28 AWG wire or smaller. 30 AWG is pretty good but any wire around 0.25mm to 0.5mm should work.
– Small file and screwdriver set
– Painter’s and kapton tape
– Metal spudger Disassemble the TouchPad
This is where you’re going to want to get that metal spudger out and be very careful not to snap clips. I can’t explain it better than iFixit already did so go check out their and then come back here.
Modify the USB Connector Board by Removing the Micro Port
There are a few ways to remove the Micro USB port. I added a bunch of flux and coated all the connectors in fresh leaded solder and then used a hot air station set to 800 degrees while wiggling the port very slightly with needle nose pliers. You don’t have to be particularly careful here so if you want to cut the port off with the dremel or the flush cuts or just rip it off with the pliers, (I don’t recommend it but…) that’s fine. We’re not using the pads it’s soldered to anyway. You should STILL be careful not to crack the board. Go slow. Be patient.
Trim the USB C Board
We need to expose the USB C port a bit on this board so let’s cut it down. Grab the painter’s tape and flip the USB C board upside down. You’ll see a small trace between the front and rear anchor points on the right side, which we don’t want to cut. Mark the tape just on the other side of that trace like I did. Dremel along the tape line until you get to the port. You can then use needle nose pliers, a flat file, and/or flush cuts to remove the rest of the board from the bottom of the port.
Prepare the USB Connector Board for the USB C Port
We need to slide the port into the old space so grab the painter’s tape again and mark off the area I marked to make room for the USB C port. You can place the port up to it like I did and use that as a guide. Grab your dremel again or a similar tool and cut out what you marked off. When you’re done, the USB C port should slide easily into the groove. It will fit tighter when we add the kapton tape in a later step.
Make Room in the TouchPad for the Added Thickness of the USB C Board
The USB C board will sit underneath the USB connector board so we have to make room by trimming away the plastic underneath. For this you’ll need to use flush cuts or any other tool you have to chip away. You could use the dremel for this if you’d like. Be careful to not go beyond the first inner layer. Beyond that is the outer shell of the TouchPad. There’s no real method here, just cut out the screw posts and chip away. Use the pictures below as a guide.
Cut the USB C Hole from the Old Micro USB Hole
To open the micro USB hole enough to fit the USB C port, take a rounded file to the left and right of both sides and just file a little bit at at time. Use a small flat file to widen the top and bottom of the port. This process is just trial and error. File a little and then grab the USB C board to test. The port will need to fit inside the hole a bit so you can push it through from the outside to test the hole size if that’s easier. Note: the USB C board will likely not rest on the bottom of the TouchPad and will float a little. This is good because it makes room for your wires and a little kapton tape underneath.
Tape the USB C Board
Since we hacked away at the USB connector board it’s possible we’ve provided the perfect environment for creating shorts! Oh no! So get out the kapton tape because we’re going to add a layer on both sides. You’ll see how I did it on one side below. Do it on both sides. You’ll also notice how I did not cover those two small square contacts just at the bottom of the tape. That’s because we need them.
Where To Get Power and Data
You’ll see the diagrams below which I’ve marked with VBUS (power), data in, data out, and ground. Obviously the old port is gone and most if its pads, but I wanted to show that both sides of the board have the connections. You could possibly do this mod differently, and if you so choose, hopefully these help.
A quick note: this mod can be done with a 4-pin USB C port. That would give you power and data just like with the USB C board I’m using in this guide, however, a 4-pin USB C board will not charge with a USB C charger (ie USB 3.1). The board I’m using in this guide provides the ability to use any charger because it comes pre-built with 5.1k resistors wired to CC1 and CC2 to ground. This is the trick that tells the USB C chargers to send power to the device.
Solder the USB C Board into the USB Connector Board
This isn’t a “how to solder tutorial” so hit up youtube and find a good tutorial that works for you. In general though, use flux, pre-tin the VBUS, Ground, D-, and D+ pads on the USB C board as well as the points on the bottom of the USB connector board.
Now for the tricky part, I didn’t list it in the Tools section above, but it would really help to have magnification or a digital microscope for this. I have these things and I used both. You might have steadier hands and better eyes than me. The picture below was my first attempt of the three TouchPads I modded, and it’s not my best soldering work, but fundamentally, this is what yours should look like.
Put the Pieces Together
You can use a bit of kapton tape to secure the wires in place a bit more if you’d like but it’s not required. It won’t short since it’s only plastic underneath. This is all press fit into place, but if you’re uncomfortable with that, you can add a little hot glue under the board as you put it back into the TouchPad. You don’t have to put the metal shield back into place if you don’t want to. It’s all a pretty tightly fit and if you find the TouchPad screen isn’t as flush as you want, just leave the metal shield off. A little kapton tape right on top would be fine instead.
Congrats, You Now Have USB C
I did this mod on three TouchPads and each one works fine with any USB charger I could find, including USB C port having USB 3.1 chargers. I can also confirm the data connection works just like it should to connect via USB mode on PC. Sadly, this doesn’t do anything to stop webOS from telling you the charger you’re using isn’t the original TouchPad barrel charger, but you can make a custom cable to stop that which I’ll cover in a future article on pivotCE.
#webOS4ever
The post first appeared on . Related posts:
-
By News Reporter
LG 1 Extends its Reach to Wider Audience With
Premium Free Content and Launch of Rerun Channel in Europe
SEOUL, Aug. 14, 2024 — LG Electronics (LG) is set to expand availability of LG 1, the company’s free ad-supported owned and operated channel, to reach a broader audience across Europe. Following a successful launch in the UK and Germany in May, LG 1 will be available later this year in France, Spain and Italy via LG Channels, the company’s exclusive free streaming service. Thanks to notable content partnerships including Lionsgate, Filmrise, NBCUniversal and Fremantle, LG has curated owned-and-operated channels to deliver a wide range of popular and premium content, demonstrating the company’s commitment to elevating the viewing experience for users in European markets.
Since its launch in the UK and Germany, LG 1 has rapidly climbed the LG Channels rankings to claim one of the top spots in viewing hours. The channel leads the way with titles such as the exclusive first-window premieres of Paul T. Goldman and Wong & Winchester as well as hit shows Nashville, Boss, Graves, The Royals, Houdini, The Girlfriend Experience, Sliders, Quantum Leap, Twelve Monkeys, New York Undercover, Mutant X, Relic Hunter, Andromeda and Anna Pihl.*
Following the success of the recent launch, LG is ensuring that LG viewers don’t miss a thing with the launch of the LG 1 time shifted channel, now live in the UK and Germany, enabling viewers to watch the channel one hour after the original broadcast.
LG is also building on the momentum of LG 1 in the UK and Germany by extending the flagship owned-and-operated channel to other regions in Europe, including France, Spain and Italy. The channel will greatly enhance the quality of viewing in these regions with a broader selection of premium content.
What’s more, LG Channels has introduced a dedicated Kids & Family tab in the UK, Germany, France, Italy and Spain, allowing families to easily explore channels specifically tailored to children, including Beano TV, Narrative and Wildbrain.*
In addition to expanded content in Europe, LG recently launched a curated premium owned-and-operated channel in the US called LG Channels Showcase, which is powered by partnerships with a wide range of film studios such as Amazon MGM Studios, Lionsgate and Sony Pictures Entertainment.
LG Channels Showcase also boasts original content such as award-winning series LG Presents: The Rivalries, The Taste of Tennessee and the recently announced Estate of Survival, the company’s first reality competition series, which will be available on LG Channels in more than nine countries, including the U.S., Canada, Australia, Korea and markets in Latin America.
The series now also streams on LG Channels Showcase, with two episodes to be released back-to-back weekly.
LG is dedicated to elevating the viewing experience for users around the world, expanding investment in partnerships and UI enhancements to deliver a more intuitive and personalized experience that aligns with viewers’ interests.
# # #
* Titles vary by market.
link hidden, please login to view -
By News Reporter
With art’s innate ability to inspire and transform our perceptions on life, LG has long championed its intersection with the most cutting-edge technology. This commitment led to the launch of the LG OLED ART project, which showcases vibrant digital canvases that celebrate the beauty of art through millions of self-illuminating pixels. This initiative has already recreated several masterpieces from world-renowned artists and fostered collaborations with some of the most distinctive contemporary artists on Earth.
In line with this initiative, LG Vietnam recently kicked off ‘The Future Becomes Now’ digital art exhibition on the first floor of Lotte Mall West Lake. This exhibition plunges visitors into the latest OLED masterpieces, highlighting a decade-long commitment to pioneering OLED technology.
To curate one of the most interactive and multi-sensory art experiences the nation has ever seen, LG Vietnam collaborated with the skilled Vietnamese visual artists of Fustic Studio. The result is an immersive art gallery experience that guides visitors on a journey through the interconnectedness of all things, from the harmonious cycles of nature to the universe and technology.
The artworks on display are being showcased on a massive canvas comprised of six expansive LG OLED TVs. Visitors can even add to each artwork’s beauty through interactive hand gestures inspired by LG OLED evo M4’s revolutionary Zero Connect technology. With cameras in front of the TV and a system behind tracking visitors’ movements, guests can create and interact with the artwork on the screen.
One of the exhibition’s focal points is its multi-sensory experience space, which reflects a contemporary trend in art viewing that seamlessly integrates sound, materials and light. Visitors can fully immerse themselves in a futuristic vision where technology and digital data harmonize with nature and the universe. Fustic Studio drew much of its inspiration from LG’s dedication to pushing technological boundaries and enriching user experiences, particularly through the breathtaking beauty of LG’s OLED masterpieces.
The exhibition also gives visitors the opportunity to explore the company’s newest OLED TVs, which come with comprehensive upgrades designed to meet consumers’ entertainment needs by excelling in four key areas: freedom, intelligence, immersion and style.
In the “Beyond Freedom” zone, visitors can experience the world’s first wireless 4K 144Hz OLED TV, the LG OLED evo M4. This model uses the Zero Connect Box to eliminate clutter from wires and peripheral devices, giving home designers the freedom to install their TV wherever they choose. LG has also enhanced the user experience by applying the latest α (Alpha) 11 AI processor to its new OLED evo M4 and G4 series, enabling them to go “Beyond Intelligence.” This upgrade delivers four times faster AI performance, 70 percent enhanced graphics performance and 30 percent faster processing speeds compared to the previous generation.
In addition, the 2024 LG OLED TV lineup promises to take users “Beyond Immersion” with screen sizes ranging from 48 to 83 inches. Even LG’s largest OLED TVs retain that trademark ultra-thin design, exuding luxury and making any living space sleeker and more stylish. The exhibition also introduced products that go “Beyond Style,” including the new LG Object Posé and LG StanbyME with various improvements. Among them, the newest Posé model uses a new OLED evo display as well as the latest Alpha 9 AI Gen 7 processor.
The LG X Fustic Studio art exhibition highlights the close relationship between art and technology through truly inspiring works. Stay tuned to
link hidden, please login to view to discover more initiatives that showcase LG’s latest innovations in uniquely captivating ways. Contributed by LG Vietnam
# # #
-
By Flavio_S
On LG OLEDs. You go on and disable SIMPLINK. Fine. But everytime you turn on your HDMI device it enables itself back again. This happens because they have disables two key features that were present in previous OSs, as you can see clearly here
link hidden, please login to view (they even put screencaps of the menus where you see the missing options in the 23) These functions are Auto Power Sync and Auto Device Detection.
Man updates are supposed to add functionalities not the other way around. It's very annoying to turn on your TV and have your AVR turn on without you wanting to.
Anyone found a solution for this problem?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.